Guide

What Is a Hammer Drill Driver?

Updated on · By the Cordless Drills Pro team

A hammer drill driver is a cordless drill that can spin a bit normally and also pulse it forward like a tiny hammer. That second action breaks up concrete, brick and stone, while the driver side still sets screws.

On this page (9 sections)
  1. What does a hammer drill driver actually do?
  2. How does the hammer action work?
  3. Bottle-size? What kind of holes will it make?
  4. What's the difference between the drill and driver modes?
  5. Do you need one, or is a regular drill enough?
  6. Which hammer drill drivers are worth a look?
  7. What should you check before buying?
  8. How do you get the best from the hammer mode?
  9. The short version

A hammer drill driver is a cordless drill with two actions: normal rotation, plus a fast forward pulse that acts like a small hammer. That pulse lets it bore into concrete, brick and stone, while the driver part still sinks screws.

The name says it: one tool handles three jobs. You get a drill for holes, a driver for fasteners, and a hammer mechanism for masonry.

That makes it the model many homeowners pick when they want a single cordless drill that covers most of the house.

What does a hammer drill driver actually do?

It rotates a bit and, in hammer mode, pushes it forward in rapid strokes while it turns. The two motions together break up hard material and clear the dust, which is why it cuts masonry a plain drill can't.

In plain drill mode the tool works like any other cordless drill. A chuck holds the bit, a trigger controls speed, and a gearbox trades torque for speed or the reverse.

The Bosch GSB18V-490B12, for instance, runs two speeds: 0-460 rpm for high-torque driving and 0-1,800 rpm for high-speed drilling.

In hammer mode a set of ridged plates inside the gearcase click past each other as the spindle turns. Each click is a small forward blow, thousands per minute.

The Bosch moves at 0-22,000 bpm, and the Craftsman V20 reaches 25,500 bpm. Those blows chip the material while the bit spins, so a 1/2-inch hole goes in with steady, light pressure instead of a hard shove.

How does the hammer action work?

A pair of toothed discs rub together as the drill spins, and the raised teeth ride up and drop, driving the bit forward. It's a mechanical trick, not a separate motor, and it only engages when you select hammer mode.

The discs are spring-loaded inside the gearcase. In drill or drive mode they're held apart and the spindle turns smoothly.

Flip the collar to the hammer icon and they mesh, so every rotation adds a series of axial blows.

That design is why a hammer drill driver stays light. The Bosch weighs 2.4 lb, and Bosch pairs the mechanism with a brushless motor that produces 490 in-lb of torque.

A rotary hammer, the next step up, uses a piston and cylinder instead and hits much harder, but it's a heavier, more specialized tool.

Because the action is mechanical, it needs a little forward pressure to bite. Let the tool do the work, hold it steady, and let the teeth chatter rather than leaning on the handle.

Bottle-size? What kind of holes will it make?

A hammer drill driver handles small to medium anchors in concrete, brick, block and stone. Think tapcon screws, wall plugs, shelf brackets and fence posts, not structural drilling.

Most models take bits up to 1/2 inch in the chuck, and the Bosch lists a 13 mm maximum chuck size. Holes around 1/4 to 1/2 inch are the sweet spot.

Bigger holes, repeated drilling, or hard aggregate concrete call for a rotary hammer with a spline or SDS chuck.

The same tool cuts wood and metal in drill mode. A sharp bit, modest speed and a little cutting oil on metal give clean results.

Just switch out of hammer first; hammering a twist bit through steel dulls it and can crack the tip.

Need to put anchors in a basement wall? Read how to drill into concrete for the bit choice, depth marking and dust control that matter most.

What's the difference between the drill and driver modes?

Drill mode is for making holes. Driver mode adds a clutch that slips at a set torque so screws stop before they strip.

Hammer mode is the third setting, for masonry.

The clutch is the driver's defining feature, and it's exactly the difference between a drill and a drill driver. A plain drill just spins; a driver lets you dial in how hard it turns a screw.

On the Bosch, the clutch has 20 plus 1 settings, so you can match the torque to the fastener and the material.

Hammer drills usually have a rotating collar with three icons: a drill bit, a screw, and a hammer. The Bosch adds Rapid Mode Selection for switching among hammer, drilling and driving.

Check the collar before every job, because driving a screw in hammer mode chews up the head and the workpiece.

Do you need one, or is a regular drill enough?

Buy a hammer drill driver if you drill into masonry more than once in a while; a regular drill is fine for wood, drywall and light metal. The hammer feature costs little extra and adds a capability a plain drill can't match.

If you only hang pictures and assemble furniture, the extra mode is dead weight. If you mount a TV bracket on a brick wall, anchor a gate post or fix shelves into a block wall, the hammer action saves you from borrowing a tool or calling someone.

The trade-off is weight and size. A hammer drill driver carries a slightly heavier gearcase than its drill-only twin.

The Craftsman V20 weighs 5.4 lb as a kit with batteries, and the Bosch is 2.4 lb bare. For overhead work, that difference shows up by the end of a job.

Our comparison of hammer drill vs regular drill lays out the cases where each one wins, so you can decide with your own project list in hand.

Which hammer drill drivers are worth a look?

These three cover a range from a light all-round kit to a pro-grade bare tool. Each one can drill, drive and hammer, so the choice comes down to budget, battery system and how hard you'll push it.

Bosch GSB18V-490B12 kit

The Bosch GSB18V-490B12 suits a homeowner who wants one capable tool for the whole house. Its brushless motor delivers 490 in-lb of torque with a 20 plus 1 clutch, and the kit includes an 18V 2 Ah battery and charger.

Rapid Mode Selection lets you flip between hammer, drilling and driving without hunting for the collar. An all-metal chuck holds bits firmly, and Bosch backs the tool with a five-year limited warranty.

Craftsman V20 CMCD711C2 kit

The Craftsman V20 CMCD711C2 is the budget choice, and it comes with two batteries and a charger that fills in an hour or less. Its 280 unit watts out and 25,500 bpm make short work of brick and block.

The 1/2-inch ratcheting chuck grips bits well, and the two-speed gearbox covers 0-350 and 0-1,500 rpm. It also clips into the Versatrack wall system if you want it off the bench.

Milwaukee 2904-20 bare tool

The Milwaukee 2904-20 suits someone already on the M18 battery platform who wants the strongest of the three. The 1/2-inch all-metal chuck has carbide teeth for grip, and the mechanical clutch keeps driving consistent.

It's a bare tool, so you supply the battery and charger from other M18 tools. Hammer mode is built for fast drilling into brick, block and concrete, and an all-metal belt clip keeps it close.

If you already run M18 batteries, this is the pick.

What should you check before buying?

Match the tool to your battery platform first, then look at chuck size, torque and weight. A drill whose batteries you already own is cheaper to run and easier to live with.

Chuck size decides your bit range: 1/2 inch is the common standard and takes the widest bits. Torque tells you how hard it drives; the Bosch lists 490 in-lb and the Milwaukee 1,400 in-lb, a big spread that reflects their different jobs.

Weight matters for overhead work.

Clutch settings matter if you drive a lot of screws; a 20-setting clutch gives finer control. Think about the kit, too.

A drill with two batteries keeps you working while one charges, while a bare tool assumes you own batteries already.

Most brands rate their hammer drills for occasional masonry, not daily concrete cutting. Be honest about how often you'll drill block and whether a rotary hammer would serve you better on bigger jobs.

How do you get the best from the hammer mode?

Use a sharp masonry bit, select hammer mode, and let the tool pulse rather than forcing it. Light, steady pressure keeps the bit cutting and stops it from overheating.

Start the hole slowly so the bit doesn't wander on the surface. Mark the spot with a punch or a piece of tape.

Clear dust every inch or so by backing the bit out while it spins, which stops the flutes clogging.

Keep the drill square to the wall. Leaning bends the bit and makes the hole oversize.

Pull out if the bit starts smoking; heat kills the carbide tip.

Our how to use a hammer drill walkthrough covers the stance, speed and bit choices in more detail. Wear eye protection and a dust mask for masonry, and check for pipes and wires before you drill.

The short version

A hammer drill driver answers the search "what is a hammer drill driver" in a sentence: it's a drill that spins and pulses, so it bores masonry and still drives screws. Pick one if your project list includes brick, block or concrete anchors.

Choose the Bosch GSB18V-490B12 if you want a light, complete kit for the house. The Craftsman V20 CMCD711C2 fits a tighter budget and brings two batteries.

The Milwaukee 2904-20 is the strongest choice for someone already invested in M18 batteries.

Buy the tool that matches your battery platform and your real jobs, not the biggest number on the box. A sharp bit and the right mode will do more for your results than extra torque.

Frequently asked questions

Can a hammer drill driver drill into steel?

Yes, in drill mode only. Turn the mode selector off hammer so the bit just cuts, use a sharp bit at low speed, and add a little pressure.

Hammer mode on metal will dull the bit fast and can damage the chuck or the workpiece.

Do I need carbide bits for masonry?

Yes. Standard twist bits won't survive the hammering.

A masonry bit has a carbide tip brazed to the end, which takes the impact and scrapes the concrete.

It also has a more open flute to clear dust as the hammer action loosens it.

Is a hammer drill driver the same as a rotary hammer?

No. A rotary hammer uses a piston-and-cylinder impact mechanism that hits much harder and is built for heavy concrete work.

A hammer drill driver is lighter and cheaper, and suits occasional anchors and small holes up to about 1/2 inch.